ANALISIS PROSES KAKI MONZA SERIES DENGAN METODE WLA DI BAGIAN TAKT 4 PRODUKSI UNIT 1 PT WLR

nanang supriyadi

Abstract


This study aims to analyze the operator workload in the Monza series leg production process in the TAKT 4 Production Unit 1 of PT Wahana Lentera Raya using the Workload Analysis (WLA) method. The process stages analyzed include lamination, trimming, touch up, and sealer. Data were collected through direct observation, interviews, and internship participation. The results of the study show the cycle time of each process: lamination 75 seconds, trimming 36 seconds, and touch up & sealer 37 seconds. With a rating factor of 1.25 and an allowance of 10%, the standard time obtained was 103.125 seconds (lamination), 49.5 seconds (trimming), and 50.875 seconds (touch up & sealer). The WLA values of each process were 1.26; 1.21; and 1.24, all of which are in the inload category. This means that the operator workload is balanced and work time has been utilized optimally.
Keyword : Workload Analysis, workload, standard time, work efficiency, manufacturing industry.

References


ADNIN, S. (2024). How to Do a Workload Analysis and Why It”s Important. https://talenthub.glints.com/en-sg/blog/workload-analysis

Dra. I. Novianingtyastuti, M.M., P. (2025). Workload Analysis: Simak Arti, Contoh & Metodenya. https://msi-indonesia.com/work-load-analysis/

Novantoro, H., & Singgih, M. (2023). ANALISIS BEBAN KERJA DAN PENENTUAN JUMLAH KARYAWAN DIVISI PRODUKSI DALAM MENYELESAIKAN TARGET DARI PERUSAHAAN (Studi Kasus PT.ABC). Jurnal Ilmiah Teknik Dan Manajemen Industri, 13, 632–644.

Prangawayu, N., Japunk, F., Anto, L., & Simangunsong, J. Y. (2023). Analisis Kebutuhan Tenaga Kerja Optimal dengan Metode Work Load Analysis ( WLA ) pada Extruder Technician I di Departemen Produksi Analisis Kebutuhan Tenaga Kerja Optimal dengan Metode Work Load Analysis ( WLA ) pada Extruder Technician I di Departemen Pr. Seminar Nasional Teknik Dan Manajemen Industri Dan Call for Paper (SENTEKMI 2021), February. https://doi.org/10.28932/sentekmi2021.v1i1.29

PT.WAHANA LENTERA RAYA. (2015). PT. WAHANA LENTERA RAYA. https://wahanafurniture.com

Ristika, N., & Prastawa, H. (2024). PENGGUNAAN METODE WORK LOAD ANALYSIS ( WLA ) DALAM PENGUKURAN BEBAN KERJA PRODUKSI JOK BUS SERI SR 2 HDDG SUITE CLASS ( SLEEPER ) UNTUK OPTIMALISASI JUMLAH TENAGA KERJA. 13, 1–8.

Vera Febriani, Prof.Dr. Aries Susanty S.T., M. T. (2019). Pengukuran Beban Kerja dan Penentuan Jumlah Tenaga Kerja Optimal Menggunakan Metode Work Load Analysis ( WLA ) Pada Bagian Packing Divisi Kacang Atom ( Studi Kasus : PT Dua Kelinci ).

Widodo, T., Fardiansyah, I., & Wiharta, T. (2020). Analisis Beban Kerja Untuk Mengetahui Jumlah Pekerja Optimal Karyawan Polishing 3 Dengan Menggunakan Metode Workload Analysis Di Pt Surya Toto Indonesia, Tbk. Journal Industrial Manufacturing, 5(2), 45. https://doi.org/10.31000/jim.v5i2.3042




DOI: https://doi.org/10.33373/profis.v14i1.8493

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

E-ISSN 2598-9987

 

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.


PROFISIENSI: Jurnal Program Studi Teknik Industri

Building A, 1st Floor, Faculty of Engineering, University of Riau Kepulauan

Jl. Pahlawan No.99, Batu Aji, Batam, Kepulauan Riau

Email: Profisiensi@journal.unrika.ac.id

 

Web Analytics Made Easy - Statcounter