EVALUASI PEMBOROSAN MESIN JUMBO LOOM BERBASIS PENDEKATAN STATISTICAL PROCESS CONTROL
Abstrak
Continuous quality control along the production line is a crucial factor in achieving high productivity. PT. TRZ is a producer of various types of plastic-based products that implement strict quality control standards. However, it is still found that production targets still need to be achieved due to machine damage. This machine breaks. The company needs to be able to fulfill consumer orders on time. This research aims to evaluate product defects resulting from damage to the Jumbo Loom machine. Statistical process control evaluates factors in cutting machine defects, thread splice marks, and sheet shrinkage. The research results show that the company faces problems regarding machine defects, including machine running, thread splice marks, and shriveled sheets. This research aims to reduce defects in machines. The Seven Tools method is used to make repairs. From the processing results on the control chart, there were daily defects that exceeded the control limits. Therefore, it was carried out using a fishbone diagram. The processing results obtained 23 indicators of the causes of the three types of defects.Referensi
Anggi Riska Devi and Widya Setiafindari, “Upaya Peningkatan Kualitas Produk Engine Pulley Yst Pro Menggunakan Metode Seven Tools Dan Kaizen Five M Checklist Di Pt Mitra Rekatama Mandiri,” J. Ilm. Tek. Mesin, Elektro dan Komput., vol. 3, no. 2, pp. 192–204, 2023, doi: 10.51903/juritek.v3i2.1743.
X. D. Crystallography, “UPAYA MENURUNKAN DEFECT SILVER STREAKS PROSES INJECTION PADA PART LENS REFLECTOR DENGAN MENGGUNAKAN METODE SEVEN TOOLS DI PT SANWA ENGINEERING,” vol. 7, no. 1, pp. 1–23, 2016.
S. S. Dahda, “Pengendalian Kualitas Pengelasan Pada Konstruksi Mechanical Piping Dengan Metode Seven Tool s,” vol. 9, no. 2, pp. 498–505, 2023.
A. Dewangga and S. Suseno, “Analisa Pengendalian Kualitas Produksi Plywood Menggunakan Metode Seven Tools, Failure Mode And Effect Analysis (FMEA), Dan TRIZ,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, no. 3, pp. 243–253, 2022, doi: 10.55826/tmit.v1iiii.42.
M. J. Firmansyah et al., “Analisis Pengendalian Kualitas Produksi Pada PT.XYZ Menggunakan Metode Seven Tools Dan FMEA,” SITEKIN J. Sains, Teknol. dan Ind., vol. 20, no. 1, pp. 231–238, 2022.
B. Harma, Farid, Susriyati, and E. P. Miliandini, “Analisis Kualitas CPO Menggunakan Seven Tools dan Kaizen,” J. Teknol., vol. 12, no. 1, pp. 13–20, 2022, doi: 10.35134/jitekin.v12i1.63.
S. M. Manaf and R. A. Darajatun, “Pengendalian Kualitas Telur Dengan Metode Seven Tools di Umkm Puyuh Kompas,” J. Ilm. Wahana Pendidik., vol. 8, no. 13, pp. 403–411, 2022.
Nofal Azhar Pratama, Marchimal Zulfian Dito, Otniel Odi Kurniawan, and Ari Zaqi Al-Faritsy, “Analisis Pengendalian Kualitas Dengan Metode Seven Tools Dan Kaizen Dalam Upaya Mengurangi Tingkat Kecacatan Produk,” J. Teknol. dan Manaj. Ind. Terap., vol. 2, no. 2, pp. 53–62, 2023, doi: 10.55826/tmit.v2i1.111.
D. Novita, D. Dewiyana, and H. Irawan, “Analisis Pengendalian Kualitas Crumb Rubber Dengan Menggunakan Metode Seven Tools Di Pt. Batanghari Tebing Pratama,” J. Ind. Samudra, vol. 3, no. 1, p. 8, 2022, doi: 10.55377/jis.v3i1.5869.
L. Permono, L. A. Salmia, and R. Septiari, “Penerapan Metode Seven Tools Dan New Seven Tools Untuk Pengendalian Kualitas Produk (Studi Kasus Pabrik Gula Kebon Agung Malang),” J. Valtech, vol. 5, no. 1, pp. 58–65, 2022.
F. S. Pratama and S. Suhartini, “Analisis Kecacatan Produk Dengan Metode Seven Tools Dan Fta Dengan Mempertimbangkan Nilai Risiko Dengan Metode Fmea,” J. SENOPATI Sustain. Ergon. Optim. Appl. Ind. Eng., vol. 1, no. 1, pp. 43–51, 2019, doi: 10.31284/j.senopati.2019.v1i1.534.
R. Prasetyo and Y. K. Bakhti, “Univeritas Veteran Bangun Nusantara /,” vol. 6, no. 1, pp. 39–51, 2022.
X. Pt, D. G. Kistianto, and I. Prakoso, “ANALISIS KUALITAS PRODUK JORAN PANCING DENGAN MENGGUNAKAN METODE NEW SEVEN TOOLS ( STUDI KASUS :,” pp. 68–79, 2023.
S. Somadi, B. S. Priambodo, and P. R. Okarini, “Evaluasi Kerusakan Barang dalam Proses Pengiriman dengan Menggunakan Metode Seven Tools,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 6, no. 1, pp. 1–11, 2020, doi: 10.30656/intech.v6i1.2008.
Suharyanto, R. L. Herlina, and A. Mulyana, “Analisis Pengendalian Kualitas Produk Waring Dengan Metode Seven Tools Di Cv. Kas Sumedang,” J. TEDC, vol. 16, no. 1, pp. 37–49, 2022.
A. Suwarno and S. B. Rahardjo, “Pengendalian Kualitas UMKM Bagus Bakery dengan Mengunakan Metode Seven Tools,” J. Tek. Ind., vol. 3, no. 1, pp. 59–65, 2022, doi: 10.37366/jutin0301.5965.
SIGMA TEKNIKA menggunakan perjanjian lisensi eksklusif. Penulis akan mempertahankan hak cipta bersama hak penggunaan ilmiah dan Universitas Riau Kepulauan akan diberikan hak penerbitan dan distribusi.
Akses penulis terbuka mempertahankan hak cipta dari makalah mereka, dan semua artikel terbuka didistribusikan di bawah syarat-syarat Lisensi Pengaitan Creative Commons (CC-BY), yang memungkinkan orang lain mendistribusikan dan menyalin artikel asalkan karya asli dikutip dengan benar.
Pengguna tidak dapat mewakili penulis sebagai dukungan adaptasi artikel mereka, dan tidak mengubah artikel sedemikian rupa untuk merusak kehormatan atau reputasi penulis.
SIGMA TEKNIKA uses an exclusive license agreement. The author will defend the copyright along with the scientific use rights and Riau Kepulauan University will be given the rights to issue and distribute.
Open author access retains the copyright of their paper, and all open articles are distributed under the terms of the Creative Commons Attribution License (CC-BY), which allows others to distribute and copy articles provided the original work is properly quoted.
Users cannot represent authors as support for the adaptation of their articles and do not change articles in such a way as to damage the honor or reputation of the author.
